Click on photo for
larger view |
JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE
4 PC board terminals, switched. Used in many modern Marshall™TM
amp models, including the JCM900 series, JCM2000 series, the Valvestate Series 1
models, and several others. Also used in many others brands of amps.
With nut and washer. Marshall part number J3B6005A or S122.
Part #J-503 |
$1.99 |
|
Click on photo for
larger view |
WASHER, FOR BRITISH STYLE (CLIFF) JACKS.
This washer goes behind the faceplate on British style plastic nut and
chrome nut jacks to provide proper spacing. Jacks come with the
washers included, but the washers are easily lost. Without the washers,
the jacks will not fit properly.
Part #W-583 |
$0.18
for each washer.
(Jacks not included). |
|
Click on photo for
larger view |
SAVE WITH MULTIPACK! JACK, 1/4", MONO PC MOUNT PLASTIC,
BRITISH STYLE,
PACK OF 6
4 PC board terminals, switched. Used in many modern Marshall™TM
amp models, including the JCM900 series, JCM2000 series, the Valvestate Series 1
models, and several others. Also used in many others brands of amps.
With nut and washer. Marshall part number J3B6005A or S122.
Part #J-503-6 |
$9.99
(Set of 6 jacks) |
|
Click on photo for
larger view |
JACK, 1/4", MONO PC MOUNT
PLASTIC, BRITISH STYLE, RED NUT, REPLACEMENT FOR Marshall™ SPEAKER JACKS.
 4 PC board terminals, switched. Used in
modern Marshall™TM
amp heads (JCM2000 series TSL and DSL, for example) as the output jack for the
speaker cabinet. With red nut and washer.
Part #J-503R |
$2.39 |
|
|
Click on photo for
larger view |
 JACK,
9-PIN Low Profile, 1/4", Marshall™, Chrome Trim Ring
Used as the
Effects A return jack and Effects B return jack on the rear panel of the
Marshall™ DSL-50, DSL-100, TSL122 and TSL-100. Chrome trim ring. Jack data here.
Nut and washer are included.
Replacement nut/washer set is the JN-916.
Part # J-560C |
$6.50 |
|
|
Click on photo for
larger view |
JACK,
9-PIN Low Profile, 1/4",
Marshall™,
Fender™, CHROME Trim Ring.
Used as the
Effects A return jack and Effects B return jack on the rear panel of the
Marshall™ DSL-50, DSL-100, TSL122 and TSL-100. Nut and washer are included.
CHROME trim ring. Jack data here.
Replacement nut/washer set is the JN-916.
Part # J-560 |
$6.50 |
|
|
Click on photo for
larger view |
JACK,
5-PIN Low Profile, 1/4", Marshall™Chrome Trim Ring.
Used as the Effects A send jack and
Effects B send jack on the rear panel of the Marshall™ DSL-50, DSL-100, TSL-122 and
TSL-100. Nut and washer are included. Note: Chrome trim ring on face of jack.
Part # J-565C |
$6.70 |
|
Click on photo for
larger view |
JACK NUT, PLASTIC,
BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.
Replacement jack nut as found on the J-503, J-504 jacks.
Part #J-5NT |
$0.50 |
|
Click on photo for
larger view |
JACK NUT MULTI-PACK - SAVE!
6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.
Replacement jack nut as found on the J-503, J-504 jacks
Part #J-5NT-6 |
$2.39 |
|
Click on photo for
larger view |
JACK NUT, PLASTIC,
BRITISH STYLE, RED
Replacement nut for the J-503, J-504.
Red nuts on these jacks typically are used on later model Marshall™ amps to
designate the 'speaker' jacks.
Part #J-5NTR |
$0.89 |
|
|
 |
NUT AND WASHER, NICKEL, KOBICONN
OR JALCO TYPE.
Fits J-506, J-506A, J-507, J-530, J-531
, J-532, J-533, J-533G,
J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560.
Part #JN-916 |
$0.75 |
|
Click on photo for
larger view |
POT,
JCM2000 SERIES 22K LINEAR BIAS ADJUST POT FOR Marshall™
Marshall part number POTTR22K, used as
bias adjust pots. Found in the DSL-50, DSL-100, TSL-100, TSL-122
models in the JCM2000. Each amplifier uses two bias pots.
Part #POT-TR22K |
$3.50 |
|
Click on photo for
larger view |
POT, 11mm, Marshall™ TYPE, PC MOUNT.
This pot has 4
pins. Includes mounting nut.
|
POT VALUE |
MARSHALL PART NUMBER |
APPLICATION |
|
B5K |
POT7 |
PRESENCE VR10 |
|
B20K |
POT2 |
REVERB A VR5, REVERB B VR6, MIDDLE
VR8 |
|
B200K |
POT5 |
TREBLE VR9 |
|
A1M |
POT6 |
CHANNEL A CLASSIC GAIN VR1,
CHANNEL A CLASSIC VOLUME VR2, CHANNEL B ULTRA GAIN VR3, CHANNEL B ULTRA VOLUME 1
VR 4, BASS VR7 |
Select Pot Value in Options
Part #P-VKG-XX |
$6.95 |
|
Click on photo for
larger view |
Complete
Marshall™ Potentiometer Kit, 10 POTS TOTAL. ORIGINAL Marshall™ REPLACEMENT PARTS.
Marshall™ MODEL DSL50 in the JCM2000 SERIES.
Complete replacement Potentiometer Kit for the
Marshall™ Model DSL50 in the JCM2000 amp series. 10 pots on the front panel.
Part #MPK-26 |
$56.95 |
|
Click on photo for
larger view |
KNOB, Marshall™, PUSH ON
D-SHAFT
Standard original Marshall™ control knob, push-on type, for D-Shaft pots used in
the following Marshall™ amp models: DSL-50 Head.
Original Marshall™ part.
The MKDS Knob is constructed so that the pointer on the front of the knob is
directly behind the flat spot in the shaft hole on the back side of the knob.Note:
In most cases, the gold color on the new knob will be deeper than the other old
knobs on your amp - the gold caps on Marshall™ knobs fade over time.
Especially true if your amp is ~20 years old.
Part #MKDS |
$2.99
(Single Knob) |
Currently unavailable from Marshall.
Has been on back-order since October, 2023. |
Click on photo for
larger view |
 Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC
CONNECTOR AT EQUIPMENT END. Common replacement cord for use on many
guitar amps, power amps, effects units, etc. Standard NEMA 5-15 plug
for North American use at 110-120 Volts AC. IEC connector at
equipment end. Used only in North America.
Part #PC-300 |
$6.95 |
|
Click on photo for
larger view |
Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END.
Replacement cord for many guitar amps, power amps, effects units, etc. 10 ft
length giveS extra flexibility in equipment placement, reduces use of extension
cords.
Standard NEMA 5-15 plug for North American
use at 110-120 Volts AC. IEC connector at equipment end.
Used only in North America.
Part #PC-600 |
$10.95 |
|
Click on photo for
larger view |
IEC POWER CONNECTOR, NON-FUSED, WIRED TYPE, SCREW ATTACHMENT TO PANEL
Popular IEC type AC connector found in many amplifiers and effects units. Designed to mount in 0.8" x 1.10" rectangular panel hole. Screw holes are 1.57" apart, center-to-center. Connectors are for push-on terminals, or may be soldered. Rated at 10 amps.
Part #P-S2-106 |
$2.95 |
|
Click on photo for
larger view |
ROCKER SWITCH, LIGHTED POWER,
ORIGINAL Marshall™ , FOUND IN Marshall™ JVM, DSL, and JCM2000 SERIES Used in the
later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later versions of
the DSL201 and DSL401, JVM410H, JVM215C, etc. Also found in the
DSL-5, DSL-15, and the Mode 4 MF-350. Has 4 electrical terminals on back of switch.
1/4" push-on terminals. Rated 16A. For use on 125VAC
or 250VAC. 15/16" x 1 1/16" x 1" deep. Internal
neon lamp. Original
Marshall part number B8C75184.
Part #SW-493C
|
$11.95 |
|
Click on photo for
larger view |
ROCKER SWITCH,
STANDBY,
ORIGINAL Marshall™ , FOUND IN Marshall™ JVM, JCM2000, DSL, TSL SERIES
Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later
versions of the DSL201 and DSL401, JVM410H, JVM215C, etc. Has 4 electrical terminals on back of switch.
1/4" push-on terminals. Rated 16A. 15/16" x 1 1/16" x 1" deep. Original
Marshall part number B8B64025B.
(For the similar standby switch used in previous model series such as the
JCM-900, early versions of the TSL and DSL series, see the SW-490 switch.)
Part #SW-490C |
$9.95 |
|
Click on photo for
larger view |
ROCKER SWITCH,
STANDBY,
WHITE, ORIGINAL Marshall™ , FOUND IN Marshall™ JVM, JCM2000, DSL, TSL SERIES
Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later
versions of the DSL201 and DSL401, JVM410H, JVM215C, etc. Has 4 electrical terminals on back of switch.
1/4" push-on terminals. Rated 16A. 15/16" x 1 1/16" x 1" deep. (For the similar standby switch used in previous model series such as the
JCM-900, early versions of the TSL and DSL series, see the SW-490 switch.)
This switch is priced to sell!
Part #SW-490CW |
$2.50 |
|
Click on photo for
larger view |
Marshall™ Impedance/Mode Selector switch.
Correct replacement for PCB mount impedance and high-low mode
switch found on
the back of many Marshall™ JCM900 and
JCM2000 series amplifiers. Also used
as
The impedance switch in Marshall™ 4x12 Cabinets (such as the 1960 series
cabinets). Found in other British-made amplifiers and cabinets
as well. Marshall™ part number S208.
Part #SW-4500 |
$13.95 |
|
Click on photo for
larger view |
ORIGINAL REPLACEMENT CAP FOR FH-815 FUSE HOLDERS - Marshall™
Cap
for the "HT" fuse holder only in the JCM2000 series (TSL100,
TSL122, DSL100, DSL50). The Mains fuse holder in the TSL and DSL models uses the FH-816 cap
(below).
Part #FH-204 |
$3.95 |
|
Click on photo for
larger view |
ORIGINAL REPLACEMENT CAP FOR FH-810 FUSE HOLDER - Marshall™
Cap for the "Mains" fuse holder found on the Marshall™ JCM2000 series
(TSL100, TSL122, DSL100, DSL50).
The HT fuse holder in the TSL and DSL models uses the FH-204 cap (above). Common failure item in Marshall™.
Designed to work with AGC type fuses (1/4" x 1 1/4") If
you would like to switch your TSL or DSL Mains Fuse to a GMA fuse (5mm x 20mm),
order the FH-815 fuse cap below.
Part #FH-816 |
$4.99 |
|
Click on photo for
larger view |
ORIGINAL REPLACEMENT
FUSE CAP KIT Marshall™ TSL100, TSL122, DSL100, DSL50
This kit contains the large fuse cap for the "Mains" fuse holder
and the small fuse cap for the HT fuse holder found on the Marshall™ TSL100, TSL122, DSL100, DSL50.
Part #FH-416 |
$8.79
(for a set of two fuse caps) |
|
Click on photo for
larger view |
ALTERNATE CAP FOR FH-810 FUSE HOLDER - Marshall™
- FOR GMA STYLE FUSE
Cap for the "Mains" fuse holder found on the Marshall™ JCM2000 series
(TSL100, TSL122, DSL100, etc). NOTE: This cap is NOT the
original cap - this cap will change the type of fuse used in in the Mains fuse
holder from the original AGC type to the GMA type (GMA is the same physical size
(5mm x 20mm) as used in the HT fuse holder).
Part #FH-815 |
$3.95 |
|
Click on photo for
larger view |
ORIGINAL REPLACEMENT FUSE HOLDER - Marshall™
Replacement for mains and HT fuse holders found on the Marshall™ JCM900
series. Replacement fuse holder for the HT fuse only in the
larger TSL and DSL models
in the JCM2000 series
(TSL100, TSL122, DSL100, DSL50). Includes the FH-204 cap (above). Common failure item in Marshall™.
Designed to work with GMA type fuses (5mm x 20mm)
Part #FH-830 |
$8.50 |
|
Click on photo for
larger view |
ORIGINAL REPLACEMENT FUSE HOLDER - Marshall™
Replacement fuse holder for the Mains fuse only in the JCM2000 TSL and DSL models
(TSL100, TSL122, DSL100, DSL50).
Includes the FH-816 cap (above). Common failure item in Marshall™.
Designed to work with AGC type fuses (1/4" x 1 1/4"). May be
converted to GMA fuses with the FH-815 cap.
Part #FH-810 |
$12.95 |
|
Click on photo for
larger view |
OCTAL TUBE KEYWAY, SET OF 2
If you have a cherished octal power
tube or rectifier with a broken keyway, here is a great solution. By cleaning
the remainder of the broken keyway from the tube base and properly installing
this keyway replacement (a little dab of silicone sealant works great to hold it
in place), your tube can safely be reinstalled into your equipment.
These great tube-savers are sold in sets of 2. Note: When using an adhesive to secure the keyway to the tube base, DO NOT use a
water-based glue. Silicone sealant (RTV) which is acryllic-based or
butyl-based is fine. Latex sealant or hot-glue is NOT.
Part #OTK8-2 |
$8.99
(for a set of 2 tube keyways) |
|
Click on photo for
larger view |
OCTAL TUBE BASE, SOLD
INDIVIDUALLY
Octal tube bases are used to construct tube socket savers, solid-state
rectifiers, bias probes, etc. 8-pin plug with room inside the base
for circuitry and wiring. Sold individually.
Part #OTB-100 |
$3.99 ea |
|
Click on photo for
larger view |
TUBE SOCKET, OCTAL 8-PIN, commonly used with the Octal Tube Base to build
bias probes, tube socket savers, tube extenders, etc. This socket
has no mounting bracket.
Part #TS-8-810 |
$4.40 |
|
Click on photo for
larger view |
9 pin Belton Micalex socket for PC board
mounting. Mounts under the PC board. Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes. Used in Marshall™ , Peavey™
and other brands.
Click here for additional specs.
Part #TS-9-BEL |
$2.79
|
|
|
Click on photo for
larger view
|
Socket - Belton,
Micalex, 8 Pin, Octal PC Mount, Long Lead
Micalex, PC mount,
long leads (Belton) - MB/MT. 1 ½" mounting centers 1 1/4" chassis hole.
Applicable for use with all types of electric and electronic equipment using
vacuum tubes. Paddle saddle mounting, easy mount with the saddle of extruded
screw hole. Phosphorous bronze pin terminal with
tin plating, glass fiber field PPS Insulating
material
Part # TS-8-209 |
$3.50
|
|
Click on photo for
larger view |
TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR EL34.
Used in Fender™ and many other amps. 1 1/2" mounting
centers. Made by Belton. Fender part number 099072500.
Part #TC-142 |
$2.25
|
|
(TUBE NOT INCLUDED)
Click on photo for
larger view |
 Revisit™ PRE-AMP TUBE DAMPER
RINGS.
Use two (or three) of these rings around a pre-amp tube to reduce noise and
microphonics. An economical alternative to more expensive tube dampers.
Will withstand high temperatures of pre-amp tubes, reusable when you change
tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. These
dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5.
Part #PTD-6 |
$4.95
(Set of 6 rings) |
|
|
 |
Diode, Silicon Rectifier, 1A, 1000PIV
Part #1N4007 |
$0.15 |
|
|
 |
Diode, Silicon Signal, 150mA, 100PIV
Part #1N4148 |
$0.12 |
|
|
 |
Diode, Silicon Rectifier, 3A, 1000PIV
Part #1N5408 |
$0.60 |
|
|
 |
Bridge, Silicon Rectifier, 8A, 600PIV
Upgraded replacement for original part KBPC602,
which tends to overheat and shut down, causing loss of preamp tube filaments. Recommend
mounting replacement bridge extended on its legs about 1/2 inch above the PC
board.
Part #KBPC806/BR86 |
$2.95 |
|
|
 |
Op-Amp, 4558, very common in amplifiers, mixers, power amps. 8-pin DIP
Part #NJM4558-D |
$1.00 |
|
|
|
Low-noise, JFET input, TL071 Single Op-Amp in 8-pin DIP package.
Also TL071CN.
Part #TL071CP |
$1.50 |
|
Click on photo for
larger view
 |
Revisit™ Reverb Tank, 17" long, 2 spring, equivalent to Accutronics 4BB3C1D. Input impedance 150 ohms, output impedance 2250 ohms, long decay (2.75 - 4.0 seconds), input insulated/output grounded.
Mounts on vertical wall, long axis horizontal, connectors down. Common replacement for Marshall™
DSL50. Also found in certain Laney™ models. See explanation of Accutronics reverb tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here.
Part #4BB3C1D"Bringing back the sound of vintage Accutronics tanks" |
$43.79
In Stock
|
|
Click on photo for
larger view |
Rubber mounting grommets for reverb tanks, package of four.
Provides shock absorption for tanks mounted directly to the inside of a wooden
amp cabinet. Mounting Hole Diameter = 3/8" Outer Diameter = 1/2"
Part #RRG-4 |
$1.99
(For a pack of 4 grommets - In Stock) |
|
|
Click on photo for
larger view |
4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 4 feet long.
Part #RC-174 |
$4.95
In stock |
|
|
Click on photo for
larger view
|
Marshall™ STYLE FOOTSWITCH W/LED Revisit™
aftermarket replacement for the original Marshall™ footswitch - same quality, just without the Marshall™ logo
and Marshall™ price tag. Sturdy metal construction. Replaces
Marshall™ stock numbers PED801 and PEDL-00001. Fits the Marshall™ DSL100, DSL201 and DSL50,
and the ValveState models AVT50, VS65R and VS30R. Also the MG Series I
model G30RCD.
Also works with the Crate VC3112 Vintage Club 30 and Crate VC5112 Vintage Club
50. Mono 1/4" Plug,
16 ft. cable. LED indicates condition of switch. Can be rewired internally to work with other amplifiers. Click here for wiring diagram.
NOTE: Will not work with many amplifiers, even those that used LEDs
on the original footswitch, without rewiring. Electronics
background suggested. Also - will generally NOT work with
amplifiers which did not have an LED indicator on the original footswitch.
Part #FBS-470L |
$33.95 |
|
Click on photo for
larger view |
Marshall™ CORNERS, FRONT OF
CABINET
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. For heads, combos and straight
speaker cabinets. Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #MC-1091 |
$10.95
(For a set of 4 corners with 12 rivets) |
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts. See the RC-1091 as a substitute set of corners.
 |
Click on photo for
larger view |
Revisit™
Quality Reproduction of Marshall™ CORNERS, FRONT OF
CABINET
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. For
Marshall™
heads, combos and straight
speaker cabinets. Replace your
Marshall™
corners with quality parts at 25% less than Marshall™
prices.
Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #RC-1091 |
$7.95
(For a set of 4 corners with 12 rivets) |
|
Click on photo for
larger view |
Marshall™
SPECIAL CORNERS, FRONT OF
SLANTED SPEAKER CABINETS
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. Two top angled corners for the
left and right top corners of angled speaker cabinets, and two straight corners for the bottom front
corners. For slanted speaker cabinets ONLY,
such as the 1960A, MG412AG, MX412A
Part #MC-1092 |
$16.95
(For a set of 4 corners with 12 rivets) |
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts.
|
Click on photo for
larger view |
Marshall™ CORNERS, REAR OF
CABINET
Rear corner set, ¾" radius. Includes 16
gold rivets for attaching to cabinet. For heads, combos and speaker
cabinets.
Part #MC-1090 |
$11.95
(For a set of 4 corners with 16 rivets) |
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts. See the RC-1090 as a substitute set of corners.
|
Click on photo for
larger view |
Revisit™
Quality Reproduction of Marshall™ Corners, Rear of
Cabinet
Rear corner set, 3/4" radius. Includes
16
gold rivets for attaching to cabinet. For Marshall™
heads, combos and
speaker cabinets. Replace your
Marshall™
corners with quality parts at 25% less than Marshall™
prices.
Part #RC-1090 |
$8.95
(For a set of 4 rear corners with 16 rivets) |
|
Click on photo for
larger view |
Marshall™
GOLD RIVETS
For attaching Marshall™ corners to cabinets. Gold, package of 12 rivets.
Part #MR-109 |
$4.95
(For a set of 12 gold rivets) |
|
Click on photo for
larger view |
Marshall™
SILVER RIVETS
For attaching Marshall™ corners to cabinets. Silver, package of 12 rivets.
Part #MR-109S |
$4.95
(For a set of 12 silver rivets) |
|
Click on photo for
larger view |
MARSHALL™
SPRUNG FOOT FOR DSL50 HEAD. Original Marshall™ Sprung foot. Sold
individually. Screws are included 3 1/4" Long, 2" Wide, 1" Tall.
2-5/16" Mounting Centers.
Part #MSF-252 |
$8.95
(each) |
|
Click on photo for
larger view |
MARSHALL™ ANTI-SKID TRAY FOR 1960A ANGLED CABINETS. Genuine Marshall™
Anti-Skid Tray. Sold
individually. For the Marshall™ 1960A slant cabinets. Gold rivets are included. 9-7/8" Long, 3" Wide, 1/8" Thick.
With Marshall™
logo.
Part #AST-1960 |
$18.65
(each)These have been on order from Marshall
since September 2023. They do not have them. |
|
Click on photo for
larger view |
MARSHALL™
CASTER CUPS FOR 1960B STRAIGHT CABINETS - SET OF 4. Genuine Marshall™
Caster Cups. Complete set of 4 for one cabinet. Package of 4 includes
16 gold rivets. For the Marshall™ 1960B straight cabinets. 3.9" Long,
2.07" Wide.
Part #MCC-1960 |
$18.95
(Set of 4) |
|
Click on photo for
larger view |
MARSHALL™
HANDLE STRAP FOR TSL100 HEAD. Original Marshall™ handle strap for the
MAH-294 Handle. Sold
individually. Includes metal strap insert and rubber strap.
Genuine Marshall. Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the worn strap! Ends
and clamps not included.
Part #MHS-294 |
$9.95
(each) |
|
Click on photo for
larger view |
MARSHALL™ END CAPS FOR MAH-294 HANDLE.
Handle end caps for the MAH-294 Handle. Sold in sets of two caps.
NOTE: DOES NOT HAVE THE MARSHALL LOGO ON THE CAPS.
Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the parts
the handle needs! Strap, screws and clamps not included. Set
of two end caps.
Part #MHC-294-2 |
$6.95
(for a set of 2 end caps) |
|
Click on photo for
larger view |
MARSHALL™ INTERNAL END CLAMPS FOR MAH-294 HANDLE.
Handle internal clamps for the MAH-294 Handle. Sold in sets of two end clamps.
Genuine Marshall.
Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the parts
the handle needs! Strap, black end caps, screws and strap not included. Note:
These are unfinished metal caps - designed to be used only with the
snap-on MHC-294-2 end caps. Set
of two end clamps.
Part #MIC-294-2 |
$4.99
(for a set of 2 end clamps) |
|
|
Click on photo for
larger view |
Marshall™
METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™
MAH-294 handle. Original Marshall™ , designed to work with the OEM
metric T-Nuts. Set of 2 Flat-head counter-sunk Phillips,
M5 x 0.8, length 25 mm.
Found primarily on
JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404 |
$1.99
(for a pack of 2 Marshall™ metric screws) |
|
Click on photos for
larger view
(Assembled)
|
Marshall™
HANDLE
Genuine Marshall™ Handle for modern heads and combo amps. Used
primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Original Marshall™ part number M-PACK-00031. Kit contains:
Part #MAH-294
|
$21.95 |
|
Click on photos for
larger view
(Assembled)
|
Marshall™
AFTERMARKET HANDLE
Identical to the Genuine Marshall™ Handle MAH-294, except does not
have the "Marshall" name imprinted on the end caps. Save compared to the price of the original Marshall™ handle. For modern heads and combo amps. Used
primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Replaces Original Marshall™ part number M-PACK-00031
or stock number MAH-294. Kit contains:
- (2) Countersunk screws - M5 x 0.8, overall
length of 25 mm
- (2) Mounting brackets
- (2) Black bracket covers (no Marshall™
logo)
- (1) Rubber handle with metallic insert
- Center-to-center screw mounting distance
is 8 3/8" (213mm).
- Overall length of assembled and mounted
handle is 101/4" (260mm).
- Replacement screws are the Marshall™ SC-404
screws, below
Part #RAH-294 |
$15.99 |
|
|
Click on photo for
larger view |
Marshall™
METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™
MAH-294 handle. Original Marshall™ , designed to work with the OEM
metric T-Nuts. Set of 2 Flat-head counter-sunk Phillips,
M5 x 0.8, length 25 mm.
Found primarily on
JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404 |
$1.99
(for a pack of 2 Marshall™ metric screws) |
|
Click on photo for
larger view |
Marshall™
LOGO, WHITE PLASTIC, 11" LONG - DSL50
The 11 inch long Marshall™ logo - large size. As used on the
DSL50
head. This logo is
11" long - please measure the old logo in order to ensure that you order the
correct size.
Part #ML-1101 |
$39.95 |
Availability date uncertain. Has been on backorder from Marshall since
May, 2023. |
Click on photo for
larger view |
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall™ METRIC
Replacements for the standard M6 metric screws used to hold the chassis in
virtually every Marshall™ head. Washers included. Package of 4
stainless steel screws, with 4 washers.
Part #MCB-4 |
$3.99
(Set of 4 screws w/washers) |
|
Click on photo for
larger view |
Marshall™ CHASSIS WASHERS
Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall™
head. Note: Not for Marshall Combo amps.
Also fits Orange and Trace Elliot amps which use chassis bolts to secure the
chassis. Package of 4 washers.
Part #MCW-4 |
$1.99
(Set of 4 washers) |
|
Click on photo for
larger view |
CHASSIS
CAGE NUTS, Marshall™ M6 METRIC, DSL50
Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall™ head. Package of 4 cage nuts. Mates with the MCB-4
screws, above.
Part #MCN-4 |
$4.59
(Set of 4 nuts) |
|
Click on photo for
larger view |
Marshall™
HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS
(SET OF 4) FOR FULL SIZE HEADS. Set of 4 screws, Stainless Steel, 1 1/2" long, Phillips, oval head, with matching cup washers.
Fits most large Marshall™ heads starting in the 1990s, including the JCM-800,
JCM-900, JCM-2000 and JVM series.
Note: The screw heads in this package have a slight oval shape, as opposed
to many Marshall™ head back panel screws which have a flat head. This oval
shape helps improve the "bite" of the screwdriver, and helps prevent the screw
head from being mangled over time.
Part #MBP-4 |
$1.49
(for a pack of 4 screws and 4 washers)
|
|
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 
