JCM900 Series Parts
JCM900 Series amps include the following model numbers:   2100, 2101, 2500, 2501, 2502, 4100, 4101, 4102, 4500, 4501, 4502, 2100SL-X, 2101SL-X, 2500SL-X, 2501SL-X, 2502SL-X

NOTE:  MARSHALL APPEARS TO BE IN SERIOUS TROUBLE, AND IS NOT SHIPPING NEW ORDERS OF

PARTS TO THE UNITED STATES AT THIS TIME.    THEY WERE BOUGHT BY ZOUNDS, INC. OF SWEDEN

ABOUT A YEAR AGO, WHO HAS NOW REBRANDED THEMSELVES AS "MARSHALL GROUP".

ONCE WE RUN OUT OF A PARTICULAR ITEM, WE ARE CURRENTLY UNABLE TO RESTOCK IT.

 

We carry an extensive selection of Marshall™ Amplifier parts for both vintage and modern amps.

Back to Marshall™ Amp Parts Index


Click on photo for
larger view		 JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE
4 PC board terminals, switched. Used in many modern Marshall™TM amp models, including the JCM900 series, the Valvestate Series 1 models, JCM2000 series, and several others.   Also used in many others brands of amps.   With nut and washer.    Marshall part number J3B6005A or S122. 
Part #J-503		 $1.99  


Click on photo for
larger view		 WASHER, FOR BRITISH STYLE (CLIFF) JACKS.
This washer goes behind the faceplate on British style plastic nut and chrome nut jacks to provide proper spacing.   Jacks come with the washers included, but the washers are easily lost.  Without the washers, the jacks will not fit properly.

 Part #W-583		 $0.18
for each washer.
(Jacks not included).		  


 Click on photo for
larger view		 JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
 4 PC board terminals, switched.  Used in many brands of amps and other equipment.   Same footprint as J-503 jack - may be used in place of J-503 to add a touch of "chrome" class to your amp!
 Part #J-603		 $2.79
(per jack)		  


 Click on photo for
larger view		 SAVE WITH MULTIPACK!  JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE, PACK OF 6
4 PC board terminals, switched. Used in many modern Marshall™TM amp models, including the JCM900 series, the Valvestate Series 1 models, JCM2000 series, and several others.   Also used in many others brands of amps.   Marshall part number J3B6005A or S122.   Pack of 6 jacks, with nuts and washers. 
Part #J-503-6		 $9.99
(Set of 6 jacks)		  


 Click on photo for
larger view		 JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE,  RED NUT, REPLACEMENT FOR Marshall™ SPEAKER JACKS.
 4 PC board terminals, switched. Used in modern Marshall™TM amp heads (JCM2000 series TSL and DSL, for example) as the output jack for the speaker cabinet.  With red nut and washer.
 Part #J-503R		 $2.39  


 Click on photo for
larger view		 JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE
Stereo jack. 6 PC board terminals, switched.  With nut and washer.  British style.
 Part #J-504		 $2.15  


 Click on photo for
larger view		 JACK, 1/4", STEREO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
6 PC board terminals, switched.  Used in many brands of amps and other equipment.   Same footprint as J-504 jack - may be used in place of J-504 to add a touch of "chrome" class to your amp!
 Part #J-604		 $2.99
(per jack)		  


 Click on photo for
larger view		 SAVE WITH MULTIPACK!  JACK, 1/4", STEREO, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE, PACK OF 6
 Stereo jack. 6 PC board terminals, switched.  Pack of 6 jacks, with nuts and washers. 
Part #J-504-6		 $10.99
(Set of 6 jacks)		  


Click on photo for
larger view

SAVE WITH OUR MULTIPACK ASSORTMENT!  THIS PACK CONTAINS THREE J-503 (4 PIN) AND THREE J-504 (6-PIN) JACKS.  
Many amps contain both the 4 pin and the 6 pin British jacks.   This assortment gives you 3 of each jack ...  Three J-503, and three J-504.    
Part # J-5034-6

$10.49
(For 3 J-503 Jacks and 3 J-504 Jacks)


Click on photo for
larger view		 JACK NUT, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS. 
 Replacement jack nut as found on the J-503, J-504 jacks.
 Part #J-5NT		 $0.50  


Click on photo for
larger view		 JACK NUT MULTI-PACK - SAVE!   6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.  
Replacement jack nut as found on the  J-503, J-504 jacks
 Part #J-5NT-6		 $2.39  


Click on photo for
larger view		 JACK NUT, PLASTIC, BRITISH STYLE, RED
Replacement nut for the J-503, J-504.  Red nuts on these jacks typically are used on later model Marshall™ amps to designate the 'speaker' jacks.
 Part #J-5NTR		 $0.89  


Click on photo for
larger view		 Complete Marshall™ Potentiometer Kit, 8 SINGLE GANG POTS AND 1 DUAL GANG POT.   ORIGINAL Marshall™ REPLACEMENT PARTS.
Complete replacement Potentiometer Kit for the Marshall™ JCM900 amp models 2100, 2101, 2500, 2501 and 2502 with 8 pots on the front panel and 1 effects level pot on the rear panel.
NOT for the JMP combo model 2100 from the 1970s.

NOT for the 2100SL-X, 2101SL-X, 2500SL-X, 2501SL-X or 2502SL-X - see the MPK-9 Potentiometer Kit for those SL-X models
 Part #MPK-1		 $24.95  


Click on photo for
larger view		 Complete Marshall™ Potentiometer Kit, 10 SINGLE GANG POTS AND 1 DUAL GANG POT.   ORIGINAL Marshall™ REPLACEMENT PARTS.
Complete replacement Potentiometer Kit for the Marshall™ JCM900 amp models 4100, 4101, 4102, 4500, 4501 and 4502 Dual Reverb with 10 pots on the front panel and 1 effects level pot on the rear panel.
Part #MPK-2		 $29.95  


Click on photo for
larger view		 Complete Marshall™ Potentiometer Kit, 8 SINGLE GANG POTS AND 1 DUAL GANG POT.   ORIGINAL Marshall™ REPLACEMENT PARTS.
Complete replacement Potentiometer Kit for the Marshall™ JCM900 SL-X amp series, including the models 2100SL-X, 2101SL-X, 2500SL-X, 2501SL-X and 2502SL-X  with 8 pots on the front panel and 1 effects level pot on the rear panel.
 Part #MPK-9		 $24.95  


Click on photo for
larger view		 Complete Marshall™ Potentiometer Kit, 17 SINGLE GANG POTS.   ORIGINAL Marshall™ REPLACEMENT PARTS.  MARSHALL 30th ANNIVERSARY 6100/6101.
Complete replacement Potentiometer Kit for the Marshall™ 30th Anniversary 6100 head and 6101 combo amplifiers with 17 pots on the front panel.
 Part #MPK-10		 $45.95  


Click on photo for
larger view		 POT, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING.  ORIGINAL Marshall™ REPLACEMENT PART.
Used in Marshall™ Valvestate I, JCM900, JCM600, JTM30, JTM60, and 6100 Series. Used in Marshall™ models: AS80R, 8040, 8080, 8100, 8200, 8240, 8280, JCM900 Models: 2100, 2101, 2500, 2501, 4100, 4500, 4101, 4102, 4501, 4502, SL-X 2100, SL-X 2500, 6100, 6101, JTM60 and JTM30 Series.  Also used in other amps besides Marshall™.   Available values:  B4.7K, B10K, B22K, B50K, A100K, B100K, B220K, and A1M.   Select Pot Value in Options
 INCLUDES NUT & WASHER  (For spare or replacement nut, order the PNW-16 nut and washer set found here).
Part #P-VM16-XX		 $2.95

Select Option:


Quantity:


Click on photo for
larger view		 POT, 10K OHM X2 LINEAR DUAL, (B10K), PC MOUNT, 6 MOUNTING PINS, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING.  ORIGINAL Marshall™ REPLACEMENT PART.
Used in Marshall™ Valvestate I, JCM900 and JCM600 Series. Also used in the JMP1 Preamp as Output Level Control.  Used in Marshall™ models: AS80R, 8040, 8080, 8100, 8200, 8240, 8280, JCM900 Models: 2100, 2101, 2500, 2501, 2502, 4100, 4500, 4101, 4102, 4501, 4502, SL-X 2100, SL-X 2500, 6100, 6101, JTM60 and JTM30 Series.  Diameter of the body of the pot is slightly smaller than a dime.  Shaft length is 11.5mm.  Fits many other amps besides Marshall™.
INCLUDES NUT & WASHER  (For spare or replacement nut, order the PNW-16 nut and washer set found here).
Part #P-V10KLX2-M16		 $6.95  


Click on photo for
larger view		 KNOB, Revisit™ Quality Reproduction of Marshall™ Knob, Push-on Knurled, Single Knob. Excellent quality aftermarket Marshall™ control knobs, push-on type.   Designed for the "knurled" type control shafts.    Black with gold top.  Used on the JCM-900 series amplifiers.   Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knob are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT		 $1.89
(Single Knob)


Click on photo for
larger view		 KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 6. Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 10 knobs.   Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.   Since Marshall™ has recently changed the appearance of their original Marshal™l brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-6		 $9.95
(Set of 6 knobs)


Click on photo for
larger view		 KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 10.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 10 knobs.   Designed for the "knurled" split-shaft potentiometers. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900, JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the earlier MG series versions as well as other models.    Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.   Older Marshalls typically have knobs where some of the gold caps have fallen off, and the other gold caps have faded to look more like silver than gold.    It used to be a bit pricey to swap out the complete set of knobs on some of the JCM900's, but with this new set of aftermarket Marshall™ knobs, it's affordable.    This set of 10 knobs is perfect for many JCM900 series models with 10 control pots, such as the 2101, 2501, 4100, 4101, 4102, 4500, 4501, and 4502.   Quality reproduction of the original Marshall™ knobs at half of the cost.  Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.
Part #MKCPT-10		 $14.95
(Set of 10 knobs)


Click on photo for
larger view		 KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 25.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 25 knobs.  Designed for the "knurled" type control shafts   Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.  Quality reproduction of the original Marshall™ knobs at half of the cost.  This set of 25 knobs is great for repair shops, at less than $1.00 per knob.    Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-25		 $24.95
(Set of 25 knobs)



Click on photo for
larger view		 KNOB SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 50.   Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 50 knobs.  Designed for the "knurled" type control shafts   Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new set of knobs.  Quality reproduction of the original Marshall™ knobs at half of the cost.  This set of 50 knobs is great for repair shops, at less than 80 cents per knob.    Since Marshall™ has recently changed the appearance of their original Marshall™ brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall™ knobs.
Part #MKCPT-50		 $39.95
(Set of 50 knobs)



Click on photo for
larger view		 Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC CONNECTOR AT EQUIPMENT END.  Common replacement cord for use on many guitar amps, power amps, effects units, etc.   Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.    IEC connector at equipment end.   Used only in North America.
 Part #PC-300		 $6.95  


Click on photo for
larger view		 Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END.  Replacement cord for many guitar amps, power amps, effects units, etc. 10 ft length giveS extra flexibility in equipment placement, reduces use of extension cords.   Standard NEMA 5-15 plug for North American use at 110-120 Volts AC.    IEC connector at equipment end.   Used only in North America.
 Part #PC-600		 $10.95  


Click on photo for
larger view		 IEC POWER CONNECTOR, NON-FUSED, WIRED TYPE, SCREW ATTACHMENT TO PANEL
Popular IEC type AC connector found in many amplifiers and effects units.   Designed to mount in 0.8" x 1.10" rectangular panel hole.   Screw holes are 1.57" apart, center-to-center. Connectors are for push-on terminals, or may be soldered.  Rated at 10 amps.
Part #P-S2-106		 $2.95  


Click on photo for
larger view		 ROCKER SWITCH, LIGHTED POWER, ORIGINAL Marshall™ , FOUND IN Marshall™ JCM900 SERIES
 For JCM900 series..  For most JCM800 models, see the SW-492.   For the JCM2000 and JVM series, see the SW-493.   Has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   Rated 22A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep.  Internal neon lamp powered by 125VAC.  Does your old Marshall™ power switch from the JCM800 era have five terminals?   See the SW-492 below, instead.
 Part #SW-491		 $12.95  


Click on photo for
larger view		 ROCKER SWITCH, BLACK, USED AS STANDBY SWITCH IN Marshall™ JCM SERIES & OTHERS  
 Has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   15/16" x 1 1/16" x 1" deep.
Part #SW-490		 $8.50  


Click on photo for
larger view		 SAVE WITH MULTIPACK!  THIS SET CONTAINS BOTH the POWER AND the STANDBY ROCKER SWITCHES, FOUND IN Marshall™ JCM SERIES & OTHERS  
 Lighted power switch has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   Rated 22A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep.  Internal neon lamp powered by either 125VAC or 250VAC.  Standby switch has 4 electrical terminals on back of switch.   1/4" push-on terminals, or solder directly to terminals.   15/16" x 1 1/16" x 1" deep. 
Part #SW-4901		 $18.95  


Click on photo for
larger view		 Marshall™ Impedance/Mode Selector switch.  Correct replacement for PCB mount impedance and high-low mode switch found on the back of many Marshall™ JCM900 and JCM2000 series amplifiers.  Also used as The impedance switch in Marshall™ 4x12 Cabinets (such as the 1960 series cabinets).    Found in other British-made amplifiers and cabinets as well.    Marshall™ part number S208.
 Part #SW-4500		 $13.95  


Click on photo for
larger view		 ORIGINAL REPLACEMENT CAP FOR FH-815 FUSE HOLDERS - Marshall™
Replacement CAP ONLY for mains and HT fuse holders found on the Marshall™ JCM900 series.
Part #FH-204		 $3.95  


Click on photo for
larger view		 ORIGINAL REPLACEMENT FUSE HOLDER  - Marshall™
Replacement for mains and HT fuse holders found on the Marshall™ JCM900 series.   Replacement fuse holder for the HT fuse only in the larger TSL and DSL models in the JCM2000 series (TSL100, TSL122, DSL100, DSL50).   Includes the FH-204 cap (above).  Common failure item in Marshall™.   Designed to work with GMA type fuses (5mm x 20mm)
Part #FH-830		 $8.50  

CAPACITOR, electrolytic 10uF @ 160V with axial leads.   Replaces 10uF @ 100V.   Used in the Marshall JCM900 series amplifiers.
Part #EL-CAP-10-160		 $1.00  

CAPACITOR, electrolytic 10uF @ 450V with axial leads.   Used in the Marshall JCM900 series amplifiers.
Part #EL-CAP-10-450		 $3.50  

CAPACITOR, electrolytic 33uF @ 450V with axial leads.   Used in the Marshall JCM900 series amplifiers.
Part #EL-CAP-33-450		 $3.99  

CAPACITOR, electrolytic 100uF @ 50V with radial leads.   Used in the low voltage power supply of Marshall JCM900 series amplifiers.
Part #RAD-100-50		 $0.39  

CAPACITOR, electrolytic 1000uF @ 16V with radial leads.   Used in the low voltage power supply of Marshall JCM900 series amplifiers.
Part #RAD-1000-16		 $0.77  


Click on photo for
larger view		 CAPACITOR, F&T BRAND, AXIAL LEAD ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS)  Made in Germany. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest capacitors available today. F&T Caps are known for their great stability and reliability.  Values available include 10uF/500V, 16uF/475V, 22uF/500V, 30uF/500V, 47uF/500V, 80uF/450V, 100uF/100V, 100uF/450V, and 220uF/300V.  Choose capacitor value under the Select Option box.
 Part #FT-CAP-XX		 Starting at
$4.95
Select Option:


Quantity:


Click on photo for
larger view		 CAPACITOR, F&T BRAND, DUAL CAN 16uF+16uF @ 450V.  Direct replacement for LCR type capacitors popular in Marshall™ and Vox™ amps.    This is a dual can style capacitor 16uF/16uF rated at 450 volts.   Solder terminals for attaching wire leads.   1 3/8" diameter X 2" tall.  Very low ripple.   Clamp may be ordered separately below.   Made in Germany.  Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest capacitors available today. F&T Caps are known for their superior stability and reliability.
Part #FT-1616		 $17.95  


Click on photo for
larger view		 CAPACITOR, F&T BRAND, DUAL CAN 32uF+32uF @ 500V.  Direct replacement for LCR type capacitors popular in Marshall™ JMP and JCM900 series amps.    This is a dual can style capacitor 32uF/32uF rated at 500 volts.   Solder terminals for attaching wire leads.   1 3/8" diameter X 2" tall.  Very low ripple.   Clamp may be ordered separately below.   Made in Germany.  Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest capacitors available today. F&T Caps are known for their superior stability and reliability.
Part #FT-3232		 $18.95  

CAPACITOR, F&T BRAND, DUAL CAN 50uF+50uF @ 500V  Direct replacement for LCR type capacitors popular in Marshall™ JMP and JCM900 series amps.    This is a dual can style capacitor 50uF/50uF rated at 500 volts.   Solder terminals for attaching wire leads.   1 3/8" diameter X 2" tall.  Very low ripple.   Clamp may be ordered separately below.   Made in Germany.  Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest capacitors available today. F&T Caps are known for their great tone and reliability.
Part #FT-5050		 $19.95  

CAPACITOR, JJ ELECTRONIC, direct replacement for LCR type capacitors popular in Marshall™ JCM900 series amps.    This is a dual can style capacitor 50uF/50uF rated at 500 volts.   Solder terminals for attaching wire leads.   1 3/8" diameter X 2" tall.  Very low ripple.   Clamp may be ordered separately below.   Made in the Slovak Republic in eastern Europe.  Founded in 1993 by Jan Jurco, JJ Electronic is a world-renowned manufacturer of vacuum tubes, electrolytic capacitors and high-end audio amplifiers.
 Part #JJ-5050		 $17.95  

CAPACITOR CLAMP, for FT-1616, FT-3232, FT-5050, JJ-5050, or other 1 3/8" diameter can style capacitors.

Part #CC-122

 $2.50  

RESISTOR, SANDBLOCK 470 OHM, 5 WATT.   
Part #470W5		 $0.99  
RESISTOR, FLAMEPROOF, 1000 OHM, 5 WATT.    Commonly used as the screen grid resistor in many tube amps.
 Part #1000W5		 $0.99  
RESISTOR, SANDBLOCK 47K OHM, 5 WATT.    4700 ohms, 5 Watt Sandblock style.
Part #47KW5		 $0.99  

Click on photo for
larger view		 TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6L6 OR EL34 TUBES.   USED IN Marshall™ AND MANY OTHER AMPS. 
Part #TC-141		 $3.49


Click on photo for
larger view		 LARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES.  

Part #TC-143		 $3.49


Click on photo for
larger view		 OCTAL TUBE KEYWAY, SET OF 2
If you have a cherished octal power tube or rectifier with a broken keyway, here is a great solution. By cleaning the remainder of the broken keyway from the tube base and properly installing this keyway replacement (a little dab of silicone sealant works great to hold it in place), your tube can safely be reinstalled into your equipment.   These great tube-savers are sold in sets of 2.   Note:  When using an adhesive to secure the keyway to the tube base, DO NOT use a water-based glue.   Silicone sealant (RTV) which is acryllic-based or butyl-based is fine.   Latex sealant or hot-glue is NOT.
 Part #OTK8-2		 $8.99
(for a set of 2 tube keyways)


Click on photo for
larger view		 OCTAL TUBE BASE, SOLD INDIVIDUALLY
Octal tube bases are used to construct tube socket savers, solid-state rectifiers, bias probes, etc.   8-pin plug with room inside the base for circuitry and wiring.  Sold individually.
 Part #OTB-100
$3.99 ea


Click on photo for
larger view		 TUBE SOCKET, OCTAL 8-PIN, commonly used with the Octal Tube Base to build bias probes, tube socket savers, tube extenders, etc.   This socket has no mounting bracket.
 Part #TS-8-810		 $4.40  


Click on photo for
larger view		 PHENOLIC TUBE SOCKET FOR OCTAL TUBES.  EXACT REPLACEMENT FOR VINTAGE FENDER, VINTAGE Marshall™ (including the JCM900 Series), and many others.    Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes.   For 1" to 1 1/8" hole.  Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/2" apart.  Unlike some phenolic tube sockets on the market, this one fits the 1" hole found in most vintage Fenders.  
Part #TS-8-600		 $5.70


Click on photo for
larger view		 PHENOLIC TUBE SOCKET FOR OCTAL TUBES.      Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes.   For 1 1/8" hole.   Bottom mounting (mounted from the inside of the chassis), mounting holes spaced 1 1/2" apart. 
Part #TS-8-250		 $5.15


Click on photo for
larger view		 TUBE SOCKET FOR MINIATURE 9-PIN TUBES.  EXACT REPLACEMENT FOR MANY MAKES AND MODELS OF AMPS WITH HAND-WIRED TUBE SOCKETS.      Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes.   For 3/4"  hole.  Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart.   Designed to work with the TR-144 or TR-146 tube retainers, or the TS-325S tube shield.
 Part #TS-9-610		 $2.49


Click on photo for
larger view		 Marshall™ SMALL BRASS PAN-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6).   Set of 6 screws, brass, 3/8" (9.5mm) long, slotted pan head - head is 5.4mm in diameter, 4-40 thread, with lock washer and nut.   Used to mount preamp tube sockets and impedance selectors in classic Marshall™ amps.
Part #MSBS-6		 $1.99
(for a pack of 6 screws, 6 lock washers and 6 nuts)
  



Click on photo for
larger view		 Marshall™ SMALL BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6).   Set of 6 screws, brass, 1/2" (12.7mm) long, slotted round head - head is 5.4mm in diameter, 4-40 thread, with lock washer and nut.   Used to mount impedance selectors and IEC power cord connectors in classic Marshall™ amps.
Part #MLBS-6		 $2.49
(for a pack of 6 screws, 6 lock washers and 6 nuts)
  



Click on photo for
larger view		 Marshall™ MEDIUM BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 8).   Set of 8 screws, brass, 3/8" (12.7mm) long, slotted round head - head is 6.1mm in diameter, 6-32 thread, with lock washer and nut.   Used to mount power tube sockets, capacitor cans and ground lugs in classic Marshall™ amps.
Part #MMBS-8		 $2.99
(for a pack of 8 screws, 8 lock washers and 8 nuts)
  


Click on photo for
larger view		 TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL WITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE .  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes.   9-Pin tube socket is made of sturdy Micalex.   Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   Requires 3/4" hole in chassis.  Solder lugs for wire connection to tube socket. Shield, base and socket. 
 Part #TS-370		 $4.99  


Click on photo for
larger view		 TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL.  Includes new base, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.  Shield and base only - socket not included.
 
 Part #TS-325S		 $2.29  


Click on photo for
larger view		 TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, SET OF 6.  Includes new bases, if needed.  Spring in top of shield fits over the tube.  Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands.  Holes in base spaced 1 1/8" apart.   This is a great kit to replaced all 6 of the tube shields in many Fender™ amps with 6 preamp tubes.  Shield and base only - socket not included.
 
 Part #TS-325S-6		 $12.95  


(TUBE NOT INCLUDED)

Click on photo for
larger view

 Revisit™ PRE-AMP TUBE DAMPER RINGS.   Use two (or three) of these rings around a pre-amp tube to reduce noise and microphonics.  An economical alternative to more expensive tube dampers.   Will withstand high temperatures of pre-amp tubes, reusable when you change tubes.   Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes.   These dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. 
Part #PTD-6		 $4.95
(Set of 6 rings)



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8DB2C1D.  Short Tank, Medium Decay, input impedance 310 ohms, output 2575 ohms, insulated input and grounded output.    Designed for horizontal mounting, open side up.   Primarily found in the Marshall™ 4100, 4101, 4102, 4500, 4501, 4502 in situations where the tank is mounted "upside down". See explanation of Accutronics reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here.  

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #8DB2C1A

"Bringing back the sound of vintage Accutronics tanks"

 $42.89  



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8DB2C1D.  Short Tank, Medium Decay, input impedance 310 ohms, output 2575 ohms, insulated input and grounded output.   Mounts on vertical wall, long axis horizontal, connectors down.   Primarily found in the Marshall™ 4100, 4101, 4102, 4500, 4501, 4502, 5150, 5205, 8080, 8100, 8240, AS50, AS50R, AS80R, AVT50, AVT50H, JCM600, JCM602, JTM310, JTM312, JTM610, JTM612, JTM615, JTM622, MA50C, G25R, G50RCD, VS100R, VS100RH, VS102R, VS230, VS232, VS265, and VS65R.    See explanation of Accutronics reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here.  

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #8DB2C1D

"Bringing back the sound of vintage Accutronics tanks"

 $42.89  



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8DB3C1B.  Short Tank, Long Decay, input impedance 310 ohms, output 2575 ohms, insulated input and grounded output.  Mounts horizontal, open side down.   Primarily used by  Marshall™ JCM900.    See explanation of Accutronics reverb tank numbering system here.   See a chart which lists AC impedance and DC resistance measurements for reverb tanks here. 

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #8DB3C1B

"Bringing back the sound of vintage Accutronics tanks"

 $42.89  



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8FB2B1F. Short Tank, Medium Decay, input impedance 1925 ohms, output 2575 ohms, grounded input and insulated output. Mounts on vertical wall with long axis vertical, output side up.   See explanation of Accutronics reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here.  

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #8FB2B1F

"Bringing back the sound of vintage Accutronics tanks"

 $42.89  



Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8FB3C1B. Short Tank, Long Decay, input impedance 1925 ohms, output 2575 ohms, insulated input and grounded output. Mounts horizontal, open side down.   See explanation of Accutronics reverb tank numbering system here.  See a chart which lists AC impedance and DC resistance measurements for reverb tanks here.  

Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.

View the 2-year warranty details here.
Part #8FB3C1B

"Bringing back the sound of vintage Accutronics tanks"

 $42.89  



Click on photo for
larger view
Rubber mounting grommets for reverb tanks, package of four.   Provides shock absorption for tanks mounted directly to the inside of a wooden amp cabinet.  Mounting Hole Diameter = 3/8"  Outer Diameter = 1/2"
Part #RRG-4		 $1.99
(For a pack of 4 grommets - In Stock)		  


Click on photo for
larger view

 3 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.  Dual cable, excellent shielding properties, 3 feet long.
Part #RC-173		 $8.95
In Stock		  


Click on photo for
larger view

 4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.  Dual cable, excellent shielding properties, 4 feet long.
Part #RC-174		 $8.95
In stock		  


Click on photo for
larger view

 5 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.  Dual cable, excellent shielding properties, 5 feet long.
Part #RC-175		 $8.95
In stock		  


Click on photo for
larger view		 Marshall™ CORNERS, FRONT OF CABINET  
Front corner set, ¾" radius. Includes 12 gold rivets for attaching to cabinet.  For heads, combos and straight speaker cabinets.   Will not fit slanted speaker cabinets, such as the 1960A.  For slanted cabinets, see the MC-1092 set.
Part #MC-1091		 $10.95
(For a set of 4 corners with 12 rivets)		 Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping parts.  See the RC-1091 as a substitute set of corners.


Click on photo for
larger view		 Revisit™ Quality  Reproduction of Marshall™ CORNERS, FRONT OF CABINET  
Front corner set, ¾" radius. Includes 12 gold rivets for attaching to cabinet.  For Marshall™ heads, combos and straight speaker cabinets.  Replace your Marshall™ corners with quality parts at 25% less than Marshall™ prices.   Will not fit slanted speaker cabinets, such as the 1960A.  For slanted cabinets, see the MC-1092 set.
Part #RC-1091		 $7.95
(For a set of 4 corners with 12 rivets)		  


Click on photo for
larger view		 Marshall™ SPECIAL CORNERS, FRONT OF SLANTED SPEAKER CABINETS
 Front corner set, ¾" radius. Includes 12 gold rivets for attaching to cabinet.   Two top angled corners for the left and right top corners of angled speaker cabinets, and two straight corners for the bottom front corners.  For slanted speaker cabinets ONLY, such as the 1960A, MG412AG, MX412A
Part #MC-1092		 $16.95
(For a set of 4 corners with 12 rivets)		 Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping parts. 


Click on photo for
larger view		 Marshall™ CORNERS, REAR OF CABINET  
Rear corner set, ¾" radius. Includes 16 gold rivets for attaching to cabinet.  For heads, combos and speaker cabinets.  

Part #MC-1090		 $11.95
(For a set of 4 corners with 16 rivets)		 Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping parts.  See the RC-1090 as a substitute set of corners.


Click on photo for
larger view		 Revisit™ Quality  Reproduction of Marshall™ Corners, Rear of Cabinet  Rear corner set, 3/4" radius. Includes 16 gold rivets for attaching to cabinet.  For Marshall™ heads, combos and speaker cabinets.   Replace your Marshall™ corners with quality parts at 25% less than Marshall™ prices.

Part #RC-1090		 $8.95
(For a set of 4 rear corners with 16 rivets)		  


Click on photo for
larger view		 Marshall™ GOLD RIVETS
 For attaching Marshall™ corners to cabinets.  Gold, package of 12 rivets.
Part #MR-109		 $4.95
(For a set of 12 gold rivets)


Click on photo for
larger view		 Marshall™ SILVER RIVETS
 For attaching Marshall™ corners to cabinets.  Silver, package of 12 rivets.
Part #MR-109S		 $4.95
(For a set of 12 silver rivets)


Click on photo for
larger view		 MARSHALL™ HANDLE STRAP FOR TSL100 HEAD.  Original Marshall™ handle strap for the MAH-294 Handle. Sold individually.  Includes metal strap insert and rubber strap.   Genuine Marshall.  Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the worn strap!  Ends and clamps not included.
Part #MHS-294		 $9.95
(each)


Click on photo for
larger view		 MARSHALL™ END CAPS FOR MAH-294 HANDLE.  Handle end caps for the MAH-294 Handle. Sold in sets of two caps.   NOTE:  DOES NOT HAVE THE MARSHALL LOGO ON THE CAPS.   Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Save money by replacing only the parts the handle needs!  Strap, screws and clamps not included.   Set of two end caps.
Part #MHC-294-2		 $6.95
(for a set of 2 end caps)


Click on photo for
larger view		 MARSHALL™ INTERNAL END CLAMPS FOR MAH-294 HANDLE.  Handle internal clamps for the MAH-294 Handle. Sold in sets of two end clamps.   Genuine Marshall.   Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Save money by replacing only the parts the handle needs!  Strap, black end caps, screws and strap not included.  Note:  These are unfinished metal caps - designed to be used only with the snap-on MHC-294-2 end caps.  Set of two end clamps.
Part #MIC-294-2		 $4.99
(for a set of 2 end clamps)


Click on photo for
larger view

 Marshall™ METRIC HANDLE SCREWS
 Pack of 2 metric handle screws for Marshall™   MAH-294 handle.   Original Marshall™ , designed to work with the OEM metric T-Nuts.   Set of 2 Flat-head counter-sunk Phillips,  M5 x 0.8, length 25 mm.   Found primarily on JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404		 $1.99
(for a pack of 2 Marshall™ metric screws)		  


Click on photos for
larger view

(Assembled)

Marshall™ HANDLE
Genuine Marshall™ Handle for modern heads and combo amps.   Used primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Original Marshall™ part number M-PACK-00031.    Kit contains:

  • (2) Countersunk screws - M5 x 0.8, overall length of 25 mm

  • (2) Mounting brackets
  • (2) Black bracket covers with Marshall™ logo
  • (1) Rubber handle with metallic insert
  • Center-to-center screw mounting distance is 8 3/8" (213mm). 
  • Overall length of assembled and mounted handle is 101/4" (260mm).
  • Replacement screws are the Marshall™ SC-404 screws, below

Part #MAH-294

 

 $21.95

DISCONTINUED BY THE "NEW" MARSHALL GROUP

 SEE THE RAH-294 (BELOW) AS AN ALTERNATIVE

 



Click on photos for
larger view


(Assembled)
 Marshall™ AFTERMARKET HANDLE
Identical to the Genuine Marshall™ Handle MAH-294, except does not have the "Marshall" name imprinted on the end caps.   Save compared to the price of the original Marshall™ handle.  For modern heads and combo amps.   Used primarily on JCM900, JCM2000, larger ValveState, and JVM series amps.  Replaces Original Marshall™ part number M-PACK-00031 or stock number MAH-294.    Kit contains:
  • (2) Countersunk screws - M5 x 0.8, overall length of 25 mm
  • (2) Mounting brackets
  • (2) Black bracket covers (no Marshall™ logo)
  • (1) Rubber handle with metallic insert
  • Center-to-center screw mounting distance is 8 3/8" (213mm). 
  • Overall length of assembled and mounted handle is 101/4" (260mm).
  • Replacement screws are the Marshall™ SC-404 screws, below

Part #RAH-294

 $15.99  


Click on photo for
larger view

 Marshall™ METRIC HANDLE SCREWS
 Pack of 2 metric handle screws for Marshall™   MAH-294 handle.   Original Marshall™ , designed to work with the OEM metric T-Nuts.   Set of 2 Flat-head counter-sunk Phillips,  M5 x 0.8, length 25 mm.   Found primarily on JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404		 $1.99
(for a pack of 2 Marshall™ metric screws)		  


Click on photo for
larger view		 Marshall™ LOGO, WHITE PLASTIC, 9" LONG - TSL122
The 9 inch long Marshall™ logo - medium size.    As used on the TSL122 combo.  This logo is 9" long - please measure the old logo in order to ensure that you order the correct size.
 Part #ML-901		 $38.95
Availability date uncertain.  Has been on backorder from Marshall since May, 2023.

Click on photo for
larger view		 Marshall™ LOGO, WHITE PLASTIC, 11" LONG - TSL100
The 11 inch long Marshall™ logo - large size.  As used on the 2100, 2205, 2203, 2204, 2210, 2550, 2553, 2554, 2558, 4102, 4001, 4210, 4211, 4212, 4100, 4101, 4103, 4010, 4500, 5213, 5210, 5212, DSL100,  1986, 1960B cabinet, 1959JMP, 1936, TSL100, 6100, 6101, JCM1959, 2558V, 3005, 2555SL, AS1960, 2100SLX, TSL60, 1987JCM,  DSL50, 3005, 1960AX,  and some other models  This logo is 11" long - please measure the old logo in order to ensure that you order the correct size.   
 Part #ML-1101		 $39.95
Availability date uncertain.  Has been on backorder from Marshall since May, 2023.

Click on photo for
larger view		 Marshall™ TOP VENT, 8 SCREW OR RIVET HOLES, MOST JCM800 AND JCM900 HEADS
This original Marshall vent is for most JCM800 and JCM900 heads from the 1980s and 1990s.   Check the measurement of your existing vent - the MV-211 vent measures 17 5/8" x 3".  Rivets/screws not included.
 Part #MV-211		 $13.95
Availability date uncertain.  Has been on backorder from Marshall since December, 2023.


Click on photo for
larger view		 STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall™ METRIC
Replacements for the standard M6 metric screws used to hold the chassis in virtually every Marshall™ head.  Washers included.   Package of 4 stainless steel screws, with 4 washers.  
Part #MCB-4		 $3.99
(Set of 4 screws w/washers)		  



Click on photo for
larger view		 STAINLESS STEEL COMBO CHASSIS SCREWS, Marshall™ METRIC (NOT BLACK!)  SET OF 4 SCREWS.
 Unpainted replacements for the standard M6 metric screws used to hold the chassis in virtually every larger Marshall™ combo (typically 50 watts & up).   Note that these screws are plain stainless steel - NOT BLACK LIKE the ORIGINALS.  You may paint the top black if you choose.  We recommend that you only paint the top - do not paint the threads.  35mm long, replaces Marshall part number MESCRW00001.   Found in the JTM610, JTM612, JTM612, JTM615, JTM622, JCM601, JCM602, 2101, 2501, 2502, 4101, 4102, 4501, 4502, TSL601, TSL601, and TSL122.   Set of 4 screws.   See the CW-400-4 washers below for a set of suitable washers.
 Part #MCS-5140-4		 $2.29
(Set of 4 screws)


Click on photo for
larger view		 CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 4 washers.
Part #CW-400-4		 $0.99
(for a set of 4 washers)		  


Click on photo for
larger view		 Marshall™ CHASSIS WASHERS
Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall™ head.   Note:  Not for Marshall Combo amps.   Also fits Orange and Trace Elliot amps which use chassis bolts to secure the chassis.  Package of 4 washers.
 Part #MCW-4		 $1.99
(Set of 4 washers)		  


Click on photo for
larger view		 CHASSIS CAGE NUTS, Marshall™ M6 METRIC
Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall™ head.   Package of 4 cage nuts.   Mates with the MCB-4 or MCS-5140-4 screws, above.
 Part #MCN-4		 $4.59
(Set of 4 nuts)		  



Click on photo for
larger view		 BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR CLOSED BACK CABINETS (SUCH AS Marshall™, Fender™ Bassman, Bandmaster, etc ).  Set of 8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with the CW-400-8 cup washers.
Part #SC-400-8		 $1.99
(for a pack of 8 screws)
  



Click on photo for
larger view		 BACK PANEL STAINLESS STEEL SCREWS (SET OF 17) FOR CLOSED BACK CABINETS (SUCH AS Marshall™, Fender™ Bassman, Bandmaster, etc ).  Set of 17 screws, Stainless Steel, 1 3/4" long, Phillips, oval head.   Use with the CW-400-17 cup washers.   A set of 17 screws completely replaces all of the screws on most Marshall™ 4x12 cabinets, including the 1960 models.
Part #SC-400-17		 $3.89
(for a pack of 17 screws)
  


Click on photo for
larger view		 CUP WASHER, STAINLESS STEEL, LARGE, SET OF 17.  OD 1/2", ID 3/16"  Typically found on larger combo amp cabinets and 4x12 cabinets, such as Marshall™ .   Set of 17 washers.  Some of the larger Marshall 4x12 cabinets, such as certain model 1960 cabinets, have 17 screws and washers in the back panel.
Part #CW-400-17		 $3.79
(for a set of 17 washers)		  



Click on photo for
larger view		 Marshall™ HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS (SET OF 4) FOR FULL SIZE HEADS.  Set of 4 screws, Stainless Steel, 1 1/2" long, Phillips, oval head, with matching cup washers.  Fits most large Marshall™ heads starting in the 1990s, including the JCM-800, JCM-900, JCM-2000 and JVM series.   Note:  The screw heads in this package have a slight oval shape, as opposed to many Marshall™ head back panel screws which have a flat head.  This oval shape helps improve the "bite" of the screwdriver, and helps prevent the screw head from being mangled over time.
Part #MBP-4		 $1.49
(for a pack of 4 screws and 4 washers)
  


Click on photo for
larger view

 Marshall™ STYLE FOOTSWITCH
Revisit™ aftermarket replacement for the original Marshall™ footswitch - same quality, just without the Marshall™ logo and Marshall™ price tag.  Sturdy metal construction.    Mono 1/4" Plug, 16 ft. cable.   Standard design - footswitch operation shorts the tip to the sleeve - will work with other makes and models of amplifiers as well as Marshall™.   Replaces Marshall™ stock numbers P801 and PEDL-00008.   Works with the Marshall™ models 1962, 8040, 2555, 2550, 2558, 2553, 2554.   JTM60 models:  JTM600-610-615-612-622.   JCM600 models 600-601-602.   JCM900 models 2100-2500-2501-2101-2502.   JTM30 models 310-312.   DBS models 7200-7400-72410-72115.  Rackmount amps 9100-9200.   MG Series I model G50RCD.    IBS models 3520-5522-3540.
 Part #FBS-470		 $29.95  


Click on photo for
larger view

 Marshall™ STYLE DUAL FOOTSWITCH
Revisit™ aftermarket replacement for the original Marshall™ dual footswitch - same quality, just without the Marshall™ logo and Marshall™ price tag.  Sturdy metal construction.  Standard design - operation of one of the footswitches shorts the tip to the sleeve, while the other switch shorts the ring to the sleeve.  Latching switches.   Replaces Marshall™ stock number P802, P803, P804, P805, PEDL-00009, PEDL-00010, PEDL-00015, PEDL-00017.   Fits the Marshall™ JCM900 series:  4100-4500-4101-4501-4102-4502.   The JCM800 series 2210-2205-4210-4212-4211.   The ValveState series:  8080-8100-8200-8280-8240.   The MG Series 1: G80RCD-G100RCD.  The Acoustic Soloist:  AS80R.

Can work with other makes and models of amplifiers as well as Marshall™ - commonly used on most models of Trace Elliot guitar amps (not the bass amps, however).   Also used on Gibson™ Goldtone amplifiers, and Framus Ruby I, Ruby II, CS, and Red Rogue models.   1/4" Stereo plug, 16 ft. cable.    Will also work on the Fender 1990s and 2000s Reissue 65 Twin-Super-Deluxe-Princeton Reverb amps.
 Part #FBS-471

 $37.95  


Click on photo for
larger view

 UNIVERSAL STYLE DUAL FOOTSWITCH WITH REMOVABLE CABLE.   Revisit™ replacement for foot switch boxes with stereo 1/4" plug for the amplifier connection.   10 foot long cable is removable from the foot switch box - has a stereo 1/4" plug for connection at both the foot switch end and the amplifier end.    Replaces Marshall™ stock number P802, P803, P804, P805, PEDL-00009, PEDL-00010, PEDL-00015, PEDL-00017.   Fits the Marshall™ JCM900 series:  4100-4500-4101-4501-4102-4502.   The JCM800 series 2210-2205-4210-4212-4211.   The ValveState series:  8080-8100-8200-8280-8240.   The MG Series 1: G80RCD-G100RCD.  The Acoustic Soloist:  AS80R.  Includes the dual footswitch box and the stereo cable (10 ft).
Advantages of the removable cable include:
  • Easy to replace cable - no disassembly or soldering needed
  • Easy to change to a different configuration footswitch by changing the cable (for example, to a mono Y-cord for Roland amps)
  • Cable has metal 1/4" plugs with spring strain reliefs for durability

Part #FBS-671

 $44.95


Click on photo for
larger view

 Marshall™ STYLE JACK PLATE, STEREO / MONO
 Marshall™ style reproduction jack plate as found on the  Marshall™ 1960A, 1960B, Vintage Modern 425A or 425B Marshall™ 4x12 cabinets.   Replaces Marshall part number M-196X-50-01.  Includes speaker wires terminated in 1/4" push-on connectors.  Made in the USA by Mojo.
Part #JP-800R

$49.95


Click on photo for
larger view

 Complete Genuine Marshall™ JACK PLATE, STEREO / MONO
 Marshall™ jack plate as found on the  Marshall™ 1960A, 1960B, Vintage Modern 425A or 425B Marshall™ 4x12 cabinets.   Marshall part number M-196X-50-01. 
Part #JP-800

$62.95


Click on photo for
larger view

 Marshall™ JACK PLATE REPAIR KIT
Replaces the common failure parts on the JP-800 mono/stereo jack plate (shown above) as found on the 1960A, 1960B, Vintage Modern 425A or 425B Marshall™ 4x12 cabinets.   Kit contains both jacks and a new mono/stereo select switch.   If the plastic housing and the PC board are intact, this kit replaces all of the functional components on the jack plate. 
Part #RK-800

$14.95


Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.  
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.

Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
  WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov